We were called from a service call  in East Lansing Mi about adding an outlet for a new dishwasher.  When we arrived at the home we found that the old dishwasher was wired directly to the service panel.  We turned off the the power to the service panel and discussed with the customer that we could wire their new dishwasher the same way as the old dishwasher or we could wire in a new outlet.  Since the dishwasher was on it's own circuit breaker, the client decided to just go ahead and have us wire the new direct.

Once the new dishwasher was wired in, we turned on the power to the service panel and tested the new dishwasher.  Everything worked great and our client was happy.

Installed generator plug on outside of home.

Installed interlock kit on panel.

Made/supplied cord for generator.

Went to home that only had partial power. Found several breakers tripped and one breaker that needed to be replaced. Reset breakers to restore power to circuits and replaced bad breaker.

Went to a home to investigate a ceiling light not working. Tested light fixture and found it to be bad. Removed bad fixture and replaced with new.

Received a call from a client in Lansing to investigate why a pull chain light in their closet was not working. We tested the fixture and found out it was bad. We turned off the power in the panel and removed the fixture. We replaced with a new pull chain fixture and bulb. We turned the power back on in the panel and tested the new fixture.

We were called to a home to investigate a plug not working in their kitchen. Found the problem to be the plug under the kitchen window was melted due to a loose connection. The wires had come loose in the box and were touching the metal box causing the breaker to trip. We turned off the power in the panel and removed the damaged plug. Installed and new plug and turned the power back on in the panel. Tested plug to ensure proper connection.

We were called to Grand Ledge to  investigate why the automatic generator would start run for about 30 seconds then shut off and not produce any voltage.

We ran several tests on the generator and found the wiring harness for the generator was damaged and needed replaced. We ordered a new harness from Generac and scheduled and appointment to replace the wiring harness for the generator. Once the wiring harness was replaced we discovered that the battery from all the times of trying to start was no longer any good and needed to be replaced.

After installing a new battery we started the generator and tested it for proper operation and correct voltage.

If you are anyone you know is having any type of electrical problem, please give us a call at (517) 627-5423 or fill out the contact form.

We were called to a home where the kitchen and bathroom plugs were not working. We tested both plugs and for that the GFCI plugs were bad. We removed and replaced these with new GFCI plugs. Upon installation they were tested and working properly for the homeowner.

We received a service call from East Lansing MI, about repairing their Riser Pipe. We installed new a new pipe and wire from panel to meter. We installed a new meter. For the riser pipe we installed new pipe and wire from meter up, wiring new wire into meter sockets. We installed two new ground rods on outside of home, installing the new ground wire from panel to ground rods.

We went to a house with a damaged Riser/Mast. We removed the old damaged riser pipe, then installed a new PVC riser pipe. We connected service wire in meter.

This required:

Grounding: Installing 2 ground rods outside of home and installing grounding wire from rods to panel.

Bonding: Installing bond wire from gas line to panel, installing bond clamp on gas line. Installing bond wire from water line to panel and installing bond clamp on water line.

Disconnecting and Reconnecting Power Lines.

We went to a home where the outlets weren't working,

We were called to a home in Grand Ledge to install a dedicated circuit for an air conditioner. The technician installed the wire, circuit and new breaker in the panel.

We were called to a home in East Lansing for wiring a hot tub.

We were called for a service call in Grand Ledge regarding several circuits in the home not working. Found the problem to be the main breaker went bad. the old main breaker was removed and a new main breaker was installed. Circuits were tested and working properly.

We had received a service call from Lansing MI, the home owner had explained 2 of their switches were no longer working, and also 3 kitchen cans. When we arrived we investigated the problem and found it to be the two switches had in fact gone bad.  We discovered the reason for the kitchen cans not working was the fluorescent bulbs would not work with the dimmer that controlled them. We installed a new single pole switch for the kitchen and installed a new dimmer switch for the kitchen cans. We tested the switches and new dimmer and everything worked correctly.

We had received a service call from Lansing MI, the home owners wanted a 30amp dedicated circuit for their dryer. We installed new wire from panel to dryer plug. We installed a new 30amp plug and installed a new 30 amp breaker in panel.

We had received a service call from East Lansing MI, The home owner had explained that their circuits were no longer working. When we arrived we investigated the problem. We removed all switches and plugs and we discoved the problem to be the GFI behind the bed was tripped. We reset the GFI and reinstalled all switches and plugs.

We were called to a home in lansing to investigate electrical plugs not working. the technician found a loose connection in the box with the wires. These wires were touching the metal box which caused the breaker to trip. The plug had to be removed due to it melting from the loose connection. A new plug was installed and all wires were tested and in good working order.

We were called to a home that needed a washer and dryer circuit to be installed. The technician ran new wiring from the panel to the location of the washer and dryer, installed new plugs, and installed new breakers in the panel for the circuits. Everything was tested and working properly.

We were called to a home where the garage plugs were not working. The technician tested the plugs and traced the problem to be a breaker in the panel that was bad. The old breaker was removed and a new breaker was installed. After the installation, the wiring in the garage was tested and was now working properly.

We were called to a home where the fridge plug was not working. Upon investigation of the outlet, we found that the wiring was loose in the box. The technician repaired the loose wiring and installed the plug properly. The plug was tested and working properly.

We were called to a home in East Lansing for wiring a hot tub.

We received a service call from Lansing MI, the home owners garage door opener plug was no longer working. We installed a new GFCI plug for garage door opener. We put wiring from the existing plug in garage to opener plug.

We had received a service call from Lansing, MI the home owner had explained that the bathroom vanity light was no longer working. We investigated the problem when we had arrived. We found the problem to be the switch that had gone bad. We supplied and installed a new single pole switch, and removed the old damaged one.

We had received a service call from Okemos MI, the home owner had explained that their kitchen lights, and plugs were no longer working. We investigated the problem and found it to be a loose joint. So we repaired the loose joint.

We were called to a home in Grand Ledge to install a dedicated circuit for an air conditioner. The technician installed the wire, circuit and new breaker in the panel.

We went to a home where the outlets weren't working,

We went to a house with a damaged Riser/Mast. We removed the old damaged riser pipe, then installed a new PVC riser pipe. We connected service wire in meter.

This required:

Grounding: Installing 2 ground rods outside of home and installing grounding wire from rods to panel.

Bonding: Installing bond wire from gas line to panel, installing bond clamp on gas line. Installing bond wire from water line to panel and installing bond clamp on water line.

Disconnecting and Reconnecting Power Lines.

We were called from a service call in Lansing. We Investigated their microwave that was not working and found plug to be working correctly and have proper voltage (wiring was a little loose on GFCI plug but should not have caused the problem the owner said).           We Found a living room plug that was damaged and that needed to be replaced.

So we removed the old damaged living room plug and supplied and installed a new plug.

We were called from a service call in Lansing, MI about repairing a old, damaged riser. We removed the old damaged riser pipe, installed a new riser and ne knob for power line. While we were out there we had also replaced a meter socket.

We received a service call from Lansing, MI about their garbage disposal not working anymore. When we arrived we investigated the garbage disposal and found the wire connection to be loose in switch. We checked the connections in plug and found that to be the problem. We tested the disposal and unit and it was working correctly when leaving.

We received a service call from Lansing, MI about their bathroom needing to be rewired, because their current wiring had a buried junction box. We installed a proper junction box in their basement. We installed new wiring from the junction box to bathroom plug and switches. We also reinstalled existing GFCI and switches.

We received a service call from Lansing MI, the home owners had explained that they wanted to have their electrical in home inspected due to water in their basement. We tested the panels and found everything to be working. the breakers and panels had been under water so we explained that that may cause problems in the future due to corrosion inside the breakers. We found 1 GFCI plug in the basement that had gone bad. We removed the old GFCI plug and supplied and replaced it with a new GFCI plug.

We received a service call from Lansing MI, The homeowners Had a circuit that wasn't working. When we arrived we investigated the circuit not working. We found the problem to be that water had been leaking through the basement window into plug box that causes the plug to go bad and short out circuit. We removed the plug and installed a GFCI plug. We then tested the circuit and everything was working correctly when leaving.

We had a service call from Lansing MI, the homeowners wanted us to take a look at their vent fan in their bathroom that had stopped working. We investigated the panel and found it to be in good order. We found the problem to be the vent fan had a bad motor and needed replacing.

We received a service call from Lansing MI, The homeowner had explained that the plugs upstairs were no longer working. When we arrived we investigated the upstairs plugs and found that the problem was the GFI tripped.

We had a service call from Lansing, MI the homeowners wanted an electrical inspection. We investigated the wiring to make sure the wiring was up to code to pass inspection. We found that the wiring was correct and in good order.

We had a service call from Lansing MI, the home owners had explained that they no longer had power. So upon arrival we tested all the outlets and discovered that some of the outlets were damages and that was causing the power to go out. So we fixed wiring for the two outlets that were damaged. All outlets were working correctly when leaving.

We received a service call from Lansing, Michigan the homeowner wanted us to come look at their outside light fixture and had explained to us that they thought it was installed improperly. Upon arrival we investigated the light fixture and discovered that it was loose and poorly installed. We removed the old light fixture, we resecured the light fixture to wall. We feted and checked wiring to light and found everything to be working correctly upon leaving.

We received a service call from Holt, Michigan the homeowners had explained that the entrance and outside light was no longer working. Upon arrival we investigated the lights that were no longer working. We discover that the breaker to be tripped. We reset the breaker to circuit and tested the lights. We found that everything to be working correctly in main entrance. We discovered that the wiring outside sensor light was wired improperly. We rewired to light and installed a new light and box.

We had received a service call from Lansing, Michigan. The homeowner explained that they no longer had power. Upon arrival we discovered that the A/C unit went bad and destroyed their 240 volt plug which shorted out the main breaker. We disconnected the A/C breaker and turned main breaker back on. We then tested the panel and found everything to be working correctly when A/C was off.

We got a Service call from Lansing MI, the homeowners explained that they no longer had power in some of the rooms in their home. Upon arrival we investigated the rooms that had no power. We found that their fuse adapter had gone bad. We replaced their old fuse adapter and upon leaving everything was working correctly.

We received a service call from Lansing, MI we installed two ground rods and grounding wire for outside disconnect for service and we reinstalled meter sockets back to home.

We received a call from Lansing, Michigan the homeowner explained that the range receptacle installed in the basement ceiling with the range cord coming through the floor to plug in needed a splice in a bad wire. And their pull chain fixture needed to be replaced. Upon arrival, we installed a new dedicated 240v range circuit and we installed a new 4wire range plug. The code required that if we change wiring to range that it be a 4 wire system. We installed a KO filler in panel, we installed a proper junction box for cut wire by panel and we installed a new wire from panel to junction box.

We had received a call from Lansing, Michigan the homeowner had explained that the service ground connection is missing jumper bond. Also, that on the first floor the GFCI protected outlet would not trip the test button and isn't operating correctly in the kitchen/bathroom. Upon  arrival we installed bonding jumper for water meter. We removed the bad GFCI plug and supplied and installed a new GFCI plug. Everything was working properly when leaving the property.

We received a call from Lansing, Michigan the homeowner explained that their outside light was no longer working. Upon arrival we investigated as to why the light was no longer working, we found that the wiring to be in good working order. They just needed a new light installed. We supplied a basic coach style outdoor light fixture. We assembled and installed the new light fixture. When leaving light was working in proper order.

We received a service call from Lansing, Michigan The homeowner explained that they needed a new plug for their washing machine. Upon arrival we removed the old plug, we installed conduit to protect the wire going down the wall. We installed a new box, and a new GFCI plug (due to being in the basement).

We had received a call from Lansing, MI the home owner had (2) Duplex plugs that no longer worked and a light fixture that was also not working anymore. Upon arrival we removed the old damaged light fixture and assembled and installed a new sconce light. We removed the two old broken plugs and supplied, installed and tested the new plugs. When we left the lights and plugs were working correctly.

We had received a call from Lansing, MI the home owner had explained that on the first floor the GFCI outlet would not trip the test button, and was not working properly in the kitchen. Also another concern was that they had outlets they were concerned were wired incorrectly. Upon arrival we tested all GFCI plugs in home and found them to be working correctly. We found (3) plugs with reverse polarity. We rewired the (3) plugs to have correct polarity.

We received a service call from East Lansing, Michigan, the homeowner had explained that they needed every accessible outside/garage receptacle needed to have GFCI protection on them. The interior metal piping needed to be bonded to the electrical service. They needed this done to pass their inspection. Upon arrival, we investigated and discover the breaker to be wired incorrectly. We rewired the breaker and everything was working correctly. We supplied and installed the GFCI plugs, we removed all old duplex plugs. We installed bonding jumper for water meter.

We received a call from Lansing, Michigan the homeowner explained that their bathroom plug no longer was working. Upon arrival we investigated the bathroom plug, and found the plug to have gone bad. So we replaced the plug with a GFCI plug. Upon leaving everything was working in the correct order.

We received a service call from Lansing, Michigan the homeowner had explained that the plug in the bathroom was no longer working. Upon arrival we investigated the plug. We discovered the GFCI plug to be tripped. We reset the GFCI plug and tested the unit, and found the plug to be working properly.

We received a call from Lansing, Michigan The owner explained that he wanted us to test some outlets to make sure that they passed inspection. Upon arrival we tested the GFCI plugs and found two to that needed to be replaced. We removed the existing plugs and plates. And we supplied and installed new plugs and plates.

We had a service call from Holt, MI the owner had explained that the bedroom light was no longer working. Upon arrival, we investigated the bedroom light. We found a loose connection in the ceiling fan. We repaired the connection and tested lights all were working correctly.

We had received a call from Okemos, Michigan the homeowner had stated that the pump plug for her pond had stopped working. When we arrived we investigated the plug. We discovered the problem was that the GFCI to be tripped and that controlled the pump for the pond. We reset the GFCI and tested it, everything was working in correct order when leaving.

We received a call from Haslett, Michigan the homeowner had explained that their light went bad and they would like us to replace it. When we arrived, we removed the existing light fixture, we tested the wiring and assembled and installed the new light fixture. We then tested the new light fixture, and everything was working properly upon leaving.

We received a call from Grand Ledge, Michigan the home owner had explained that they needed a new GFCI plug for their water heater. So when we arrived we wired and installed a 20 AMP dedicated Circuit.

We had received a call from Lansing, Michigan the owner had needed us to install heat tape. When we arrived we installed a dedicated 240 Volt circuit for the rooftop. We installed new wiring from the panel to the rooftop unit. We installed a new breaker in the panel. the unit was to run 24 hours per day.

We received a call from Grand Ledge, Michigan the homeowner explained that they needed their furnace wired in. When we arrived we installed new wiring from panel to furnace. We installed new piping and switch on furnace. We installed a dedicated circuit from the panel to quad plex for furnace equipment. We installed a new breaker in panel for plugs, and we installed a new GFCI plug and duplex plug.  We installed wiring from existing circuit to transformer for zoning board. we installed a dedicated 30 AMP A/C circuit. And we installed a new GFCI plug for peer vent water heater.

We received a call from, Grand Ledge, Michigan the owner had explained that they needed a new circuit for their boiler. When we arrived we installed a dedicated 20amp circuit. We installed a new breaker lock in the panel. And we installed new wiring for the boiler.

We received a call from DeWitt, Michigan the owner had stated that they needed a new circuit for the furnace dehumidifier and power vent. When we arrived we installed a new breaker in the panel, and we installed a new GFCI plug. We tested both and they were working correctly upon leaving.

We had received a call from Lansing, Michigan the owner had explained that they wanted 6 smoke detectors installed. Upon arrival we supplied, installed, and tested the smoke detectors. 4 upstairs, 1 on the main floor, and  1 in the basement.

We had received a call from Lansing, Michigan the tenant had explained that there was a leak in the roof and water was running down into the wiring and light fixture. They wanted us to come look at the wiring and light to verify that the wiring and light fixture was not damaged by the water. Upon arrival we tested the wiring and light and discovered that the wiring was still good, but the light lens was damaged. We removed the old damaged lens, we supplied and installed the new lens. We tested the light and everything was working correctly upon leaving.

We received a call from Lansing, Michigan the owner had stated that they wanted (2) Light fixtures installed. Upon arrival, We assembled and installed 4FT fluorescent lights. We tested the lights, and upon leaving Lights were working correctly.

We had received a call from DeWitt, Michigan. The homeowners wanted to put a heater in there new pool. Upon arrival, we installed new wiring. We wired from outside control panel to new heater. We tested the new heater and everything was working correctly when leaving.

We had received a call from Fowler, Michigan The home owner had stated that they had a new pool and needed it to be wired. Upon arrival we installed circuits and the wiring for the heaters. We installed a transformer, We installed wiring from the lights to the transformer, and installed wiring from control panel to transformer. We installed feeder wiring from the main outside panel to control panel. We installed the wiring inside the control panel. We also installed a 50amp GFCI breaker in main panel. We installed low voltage control wiring for the control panel and we installed bonding wire to all pool equipment. We tested everything and when leaving everything was working correctly.

We received a call from Mason, Michigan about having the homeowners pool wiring installed. Upon arrival we installed a 240 Volt pool pump circuit. We installed GFCI breaker in panel for pump, and wired the pump in. We supplied and wired in a 240 Volt time clock. We wired in the heater. We installed GFCI breaker for salt generator and wired the salt generator. We installed outside panel. We installed a new plug for servicing equipment. We wired in the new pool lights. We also connected bond wire to all the pool equipment. We tested everything and found everything to be working properly upon leaving.

We received a call from Haslett, Michigan the home owner had explained that they had gotten a new pool and wanted us to come out and wire it in for them. Upon arriving we installed the wiring for the pool heater, and installed the GFCI breaker for the heater. We supplied wired and installed the time clock. We installed wiring for pool pump, and installed GFCI barker for the pump. We then wired and installed a service plug. We mounted and installed wiring for salt generator. We connected all pool equipment to bonding wire. We tested everything and upon leaving everything was working correctly.

We received a call from Okemos, Michigan the home owner had stated they wanted us to come out and install some wiring for the pool they had bought. Upon arrival we wiring dedicated GFCI circuit for pool heater, and wired the pool heater unit. We wired time clock to control pumps. We installed and wired pool lights. we installed and wired in service plug for pool equipment. We installed and wired a switch for the pool cover.

We had received a call from Grand Ledge, Michigan The homeowner explained that she had a outdoor plug that was no longer working. When we arrived we investigated the plug that kept shutting off. We discovered the plug to not have a box. We installed a proper box which keeps water from getting into the plug. We tested the plug and upon leaving the plug was working correctly.

We received a call from Okemos, Michigan about a couple kitchen plugs that were no longer working in the owners kitchen. When we arrived we investigated the kitchen plugs that were no longer working and discovered that the problem was loose wire connections in the GFCI plug. We properly reinstalled wiring to GFCI plug. Upon leaving we tested the plugs and found everything to be correctly working.

We received a call from DeWitt, Michigan the owner had wanted to replace his post light by his driveway. When we arrived we supplied, assembled and installed a new light. We tested the new light and upon leaving the light was working correctly.

We received a service call from Lansing, Michigan the owners kitchen lights were not longer working. We investigated the kitchen lights, and found the bulbs to be blown and the socket tabs to be bent back inside the socket. We repaired the light sockets and installed new bulbs. Upon leaving we tested the lights and all were working correctly.

We received a call from Lansing, Michigan the owner had explained that he wanted some outdoor light fixtures replaced. When we arrived, removed old exit lights due to having no battery backup. We supplied and installed new battery backup exit lights. We removed and disposed the old battery. We supplied and installed a new battery. We removed existing wiring and piping going to dusk/dawn light due to not being legal. We suppled and installed proper piping and wiring to lights. We removed the bad dawn/dusk lights, and supplied and installed new lights. We tested all the lighting and upon leaving everything was working correctly and up to code.

We received a call from Grand Ledge, Michigan The homeowner explained that his generator was no longer working. When we arrived we investigated the generator and discovered that he needed his Generator needed to be serviced. We changed the oil, oil filter, air filter, and spark plugs. We tested the generator and upon leaving everything was working properly.

We received a call from Williamston, Michigan the homeowner had explained that he needed his riser repaired. When we arrived we investigated the riser and discover it was damaged. We removed the old damaged riser pipe, installed a new riser pipe. We installed new wiring for riser. We also installed new straps and knob. We tested the riser and everything was working correctly upon leaving.

We received a call from Lansing, Michigan the homeowner explained that her range plug was broken. When we arrived we removed the broken range plug. We supplied, and installed new wiring in the new plug. We tested the new range plug and upon leaving range plug was working correctly.

We received a call from Lansing, Michigan the homeowner had explained that her hot tub was no longer working and thought it could be an electrical problem and would like us to come look at it. When we arrived we investigated the hot tub. We discovered that the GFCI breaker had gone bad.  We supplied and installed a new GFCI breaker. We tested the tub and found everything to be working correctly upon leaving.

We received a call from Grand Ledge, Michigan the owner had explained that she would like to replace some of her old light fixtures. When we got there we removed the existing light fixtures, and installed new light fixtures. We then tested all the light fixtures and the light fixtures were working correctly upon leaving.

We had received a call from Charlotte, Michigan the homeowner explained that her generator had stopped working, and would like us to come take a look at it. When we arrived we discovered that she needed her generator serviced. We changed the oil, oil filter, air filter, and spark plugs. We tested the generator and everything was working in correct order upon leaving.

We had received a call from DeWitt, Michigan the homeowner had explained that he would like us to come out and check his smoke alarms. When we arrived,  we checked all the smoke detectors in the home. We replaced (2) 9 Volt batteries that went bad. We fixed the wiring to the smoke detector in the master bedroom. We then tested all the smoke detectors and the alarms all worked correctly upon leaving.

We received a call from DeWitt, Michigan The homeowner had wanted a camera door bell unit. When we arrived we installed a new camera door bell unit. We installed a conduit pipe to lengthen the wired up to 5ft Height. We added an extra wire to lengethen the unit. We aimed the camera to see the front door. We tested the camera and door bell and upon leaving everything was working correctly.

We received a call from Lansing, Michigan the owner had explained that the breaker kept shutting off and would like us to come take a look at it. When we arrived we investigated the breaker and found the breaker to be bad. We removed the old breaker and supplied and installed a new breaker. We tested the circuit and everything was working correctly upon leaving.

We had received a call from Lansing, Michigan the owner had explained that the circuit was tripping. When we arrived we investigated the circuit that kept tripping. We found (2) plugs to be bad, and needed to be replaced.We supplied and installed (2) new GFCI plugs. The GFCI plugs were needed due to wiring having no ground.

We received a call from Mason, Michigan the homeowner had explained that they would like a plug installed in their living room. When we arrived we installed a new plug in the living room. We installed new wiring from a new switch to a new plug. We installed a new box, plug and plate. We tested the plug, and upon leaving everything was working correctly.

We received a call from Portland, Michigan The home owner had explained that he would like a new GFCI plug on the outside of his home. When we arrived we investigated outside plug that was not working at times. We found that the GFCI plug to be bad and needed a new cover. We supplied and installed a new GFCI plug and weather proof cover. We tested the new plug and it was working correctly upon leaving.

We received a call from Lansing, Michigan to come do maintenance on the homeowners riser. When we arrived we removed the old riser pipe and wire. We installed new PVC pipping and weather head. We installed new straps for riser, and new wiring. We also installed new knob for power lines. We tested the riser and the riser was working correctly upon leaving.

We had received a call from East Lansing, Michigan the home owner had stated that the vent fan was no longer working. When we arrived we investigated if the attic vent fans were working correctly. We discovered that (1) thermostat was not working correctly and needed to be replaced. We removed the thermostat that was bad. We supplied and installed the new thermostat. We tested the vent fan and it was correctly working upon leaving.

We received a call from Eaton Rapids, Michigan the owner had stated that she would like a new plug in her bedroom. When we arrived, We installed a new plug and plate. We installed a new box, and we checked wiring for proper voltage. We tested the plug and everything was working correctly upon leaving.

We received a call from Lansing, Michigan the owner had explained that he would like us to come install a circuit. When we arrived we installed a new 30amp circuit from the panel to a/c location. We installed a new 30amp breaker in the panel. We supplied and installed a new disconnect. Disconnect comes with GFCI plug. We wired GFCI plug. We tested the circuit and GFCI plug. Upon leaving everything was working correctly.

We received a call from Grand Ledge, Michigan the owner had explained that their post light was no longer working and would like us to come take a look at it. When we arrived we investigated the light that wasn't working. We found the problem to be the transformer and bulb were bad and needed replacing. We supplied and installed a new 24 volt transformer, and a new 24volt light bulb. We tested the post light and light was working correctly upon leaving.

We received a call from Grand Ledge, Michigan the homeowner had stated that they would like us to come out and replace their meter socket that had gone bad. When we arrived we removed the old meter socket. We disconnected panel wiring in meter socket. We then installed a new meter socket, reinstalling wiring from panel to new meter and reinstalling wiring going to consumers lines. We tested the new meter socket and upon leaving the meter socket was working correctly.

We received a call from Dimondale, Michigan the owner had explained that their outdoor lights were not longer working correctly. When we arrived, we investigated the outdoor lighting. We found that the wiring was installed incorrectly. We rewired lighting, tested the lights that we rewired and upon leaving all outdoor lighting was correctly working.

We received a call from East Lansing, Michigan the owner had explained that the plug in their laundry room was not working correctly and would like us to come out and take a look at it. When we arrived we investigated the plug, we discovered that the plug had reverse polarity. We rewired the plug to fix the reverse polarity. We then tested the plug and upon leaving the plug was working correctly.

We received a call from Williamston, Michigan about putting in some GFCI plugs. When we arrived we removed (3) duplex plugs that had no ground. We then supplied and installed (3) tamper proof GFCI plugs (due to lack of a ground wire). We tested the new GFCI plugs and the plugs were working correctly upon Leaving.

We received a call from Okemos, Michigan the homeowner had explained that he would like us to take a look at a couple duplex plugs in his home that were not working correctly. When we arrived we investigated the plugs and found them to need replacing. We supplied and installed tamper proof duplex plugs. We then tested the plugs and upon leaving the plugs were working correctly.

We received a call from Grand Ledge, Michigan the homeowner had explained that he wanted us to install a generator plug. When we arrived we installed a new plug for the generator.  We installed new wiring from the plug to the main panel. We installed generator breaker in the panel. We supplied a 25 ft cord for the generator. We supplied and installed an interlock kit on the main panel. The interlock kit makes it so that the main breaker and generator breaker cannot be on at the same time. We tested the generator plug and interlock kit upon leaving and they both were working correctly.

We received a call from Lansing, Michigan the owner had explained that she would like us to come out and put in some new lights for her shop. When we arrived we removed the existing wall mount and supplied new LED walk mount fixtures.  We then tested the new light fixtures and upon leaving the fixtures were working correctly.

We received a call from Grand Ledge, Michigan the owner had explained that he had a few light fixtures he would like us to come replace. When we arrived we removed the old light fixtures. We assembled, and installed the new fixtures. We then tested the new light fixtures and upon leaving the lights were working correctly.

We received a service call from Lansing, Michigan the owner had explained that their kitchen plugs were no longer working. When we arrived we investigated the kitchen plugs that were no longer working. We found the problem to be the breaker that melted inside panel. The breakers appeared to be damaged from moisture that had gotten inside the panel. We discover that the breakers needed to be replaced. We supplied, and installed the new breakers. We then tested the voltage in the plugs. We found everything to be working correctly upon leaving.

We received a call from Lansing, Michigan the owner had explained that he wanted a utility light installed. When we arrived we installed a new keyless light fixture. We installed a new 100watt bulb for the fixture. We also put new wiring from existing light to the new light fixture. We tested the new utility light and upon leaving the new fixture was working correctly.

We received a call from Eagle, Michigan the owner had explained that he wanted us to come out and supply/install LED pack lights. When we arrived we installed lighting for the parking lot. We removed the outside existing lights. We installed a new PVC pipe from existing location to a new location. We installed new wiring from existing light to the new lights. We installed the new light and we painted the PVC pipe white. We tested the lights and they were working correctly upon leaving.

We received a call from Holt, Michigan the home owner explained that he his riser needed to be serviced. When we arrived we removed the old riser pipe, and wiring. We installed a new riser pipe and weather head. We strapped the new pipe. We installed new wiring for riser. We connected riser wires to meter socket. We tested the new wiring and piping and upon leaving everything was in its correct order.

We received a call from Lansing, Michigan the owner had explained that he wanted us to come out and install a new sump circuit for his sump pump. When we arrived we installed a dedicated 15amp circuit for sump plug. We installed a new GFCI plug for sump, we also installed a new breaker fuse in panel. We tested the new circuit and upon leaving the new plug/circuit was working correctly.

We received a call from Lansing, Michigan the owner had explained that he needed maintenance done to his riser. When we arrived we removed the old damaged riser pipe. We installed new PVC riser pipe, and weather head. We installed a new knob, also installed new wiring into riser. We tested the new riser pipe and everything was correctly working upon leaving.

We received a call from Grand Ledge, Michigan the owner had explained that he would like us to install a generator plug. When we arrived we installed a generator plug on the outside of the home. We installed wiring from plug to the main panel. We installed a generator breaker in the main panel. We installed interlock on the main panel. The interlock kit makes it so the main breaker and generator breaker cannot be on at the same time. We supplied a 10ft cord to go from the generator to the generator plug. We tested the breaker and plug we installed and upon leaving everything was working correctly.

We received a call from East Lansing, Michigan The homeowner had explained that she wanted an electrical inspection done on her home. We investigated the aluminum wiring in the home, and found it to be in good working order. The wire showed no signs of heat or corrosion damage. We investigated underground plugs, we found the wiring not to have a ground. We found one plug which had been changed to grounded plug. We removed grounded plug that had no ground. We supplied and installed a new GFCI plug, because code requires a GFCI plug due to no ground wire. We tested the new plug and upon leaving everything was working correctly.

We received a call from East Lansing, Michigan the homeowner explained that their dryer breaker kept tripping, and she would like us to come out and take a look at it. When we arrived we investigated the dryer breaker. We found the breaker to be going bad, and needed to be replaced. We supplied and installed a new 30amp 240volt breaker. We tested the voltage and breaker was working correctly upon leaving.

We received a call from East Lansing, Michigan the homeowner had explained that he would like maintain ace done on his meter and riser. When we arrived we removed the old meter socket, and installed a new meter socket. We installed new wiring from the panel into the meter socket. We removed the old riser and wire, and installed a new riser pipe, new straps,new wire for the riser and a new knob for the power lines. We installed two new ground rods on the outside of the home also we installed grounding wire from rods to the panel. We tested the meter and riser and upon leaving they were both working correctly.

We received a call from Lansing, Michigan the owner had explained that he needed a sub-panel installed due to the fact that his existing panel was too full. When we arrived we supplied and installed a sub-panel next to the main existing panel. We tested the sub-panel and upon leaving, sub-panel was working correctly.

We received a call from Grand Ledge, Michigan The home owner had explained that the generator she had would no longer start. When we arrived we investigated the generator and discovered that the starter had gone bad and needed to be replaced. We removed the old starter, supplied, and installed a new starter. We tested the generator starter, upon leaving the starter was working correctly.

We received a call from Lansing, Michigan the home owner had explained that he would like us to come out and install a generator plug for his existing generator. When we arrived we supplied and installed a plug for the generator. We installed wiring from the plug to the generator panel. We supplied a 10ft cord for the generator. We tested the generator plug and upon leaving the generator plug was working correctly.

We received a call from Lansing, Michigan the owner had explained that his riser was damaged and would like us to come out and fix it. When we arrived we removed ridged mast, hub, and removed the weather head. We installed a new ridged mast, weather head, and knob. We installed bonding line to panel. We tested the new riser and everything was working correctly upon leaving.

We received a call from Lansing, Michigan the homeowner had explained that the vent fan in his bathroom was no longer working and would like us to replace it. When we arrived we removed the old vent pipe, supplied and installed a new insulated vent pipe. We supplied and installed a new vent fan/light. We removed the old wiring from bathroom and installed new wiring. We installed new GFCI plugs and switches. Upon leaving we tested the new, light, fan, and GFCI plug. Upon leaving everything was working correctly.

We received a call from Lansing, Michigan the homeowner had explained that he had a couple duplex plug he would like replaced/installed. When we arrived we removed the old duplex plugs. We supplied and installed new tamper proof duplex plugs. We noticed that there was a loose connection in a couple of the plugs and we fixed the wiring to those. We supplied/installed new tamper proof plugs and plates. We tested the new plugs and upon leaving the plugs were working correctly.

We had received a service call from Grand Ledge, Michigan about the home owner wanted us to come install an outdoor light fixture. When we arrived we supplied, wired and installed outdoor light fixture. Upon leaving we tested the light fixture and the light was working correctly.

We received a call from Grand Ledge, Michigan the homeowner had explained that he needed a new circuit installed for his dishwasher. When we arrived we installed a new dedicated circuit. We installed a 15amp wire from the panel to the dishwasher, and installed a new breaker in the panel. We wired in the dishwasher, tested the new circuit and upon leaving circuit was working correctly.

We received a call from Eagle, Michigan about installing a Dedicated Dehumidifier circuit installation. When we arrived, we installed a new circuit from panel to utility room, also installing a new GFCI plug for the dehumidifier. We installed a new breaker in the panel for circuit. Due to the panel being in finished room we needed to cut a hole in the ceiling to get the wiring into the panel, and installed an air grate to cover the hole when we finished.

We received a service call from Eagle, Michigan the homeowner had explained that their basement lights, water softener, and sump charger were not working. When we arrived we tested the plugs and found the wiring to be correct. We traced wiring and found that the GFCI plug to be tripped. We rester the GFCI and tested the plugs for proper wiring and voltage, and found everything to be working correctly upon leaving.

We received a service call from Grand Ledge, Michigan the homeowner had explained that the switch was popping. When we arrived, we investigated the switch and discover that the switch was bad and needed to be replaced. We supplied and replaced the switch. We tested the new switch and upon leaving the switch was working correctly

We received a call from Williamston, Michigan The homeowner had explained that he would like a light fixture installed at the bottom on his stairs. When we arrived we supplied wired and installed the light fixture. Upon leaving we tested the new light fixture, the light was working correctly.

We received a call from Williamston, Michigan the home owner had explained that he would like for us to come out and install a floor plug. When we arrived we supplied and installed a brass floor plug. We put wiring from the existing circuit to the new plug. We testing the plug to make sure the wiring was correct. Upon leaving everything was wired correctly.

We received a call from East Lansing, Michigan the homeowner he explained that he would like us to come out and wire in his fireplace insert. When we arrived we installed the wiring from existing power source to the fireplace. We wired the fireplace insert in. We tested the new fireplace and upon leaving the fireplace insert was working correctly.

We received a call from Ovid, Michigan the homeowner had explained that he would like us to replace his pull chain for his light fixture. When we arrived, we removed the fixture from the ceiling, We removed the old damaged pull chain. We supplied and installed a new pull chain. We tested the new pull chain and fixture and it was working correctly upon leaving.

We received a call from Ovid, Michigan the homeowner had explained that he would like us to come out and install a plug for his generator. When we arrived, we installed a new plug on the outside of his home. We installed wiring from the new plug to the panel. We installed generator breaker in the panel. We supplied and installed cord end on existing cord.

We received a call from Lansing, Michigan the homeowner had explained that he would like us to come out and repair his riser. When we arrived, we installed a bond wire from the panel to the gas line then installed a bond clamp on the gas line. We installed bond wire from the panel to the water line, then installed a bonding clamp on the water line. We installed two ground rods on the outside of the home. We installed grounding wire from ground rods to panel. The panel was damaged so we removed the old damaged panel. We installed a new 30 space 100amp panel. Upon leaving we tested the panel and riser and both were working correctly.

We received a call from Ovid, Michigan the homeowner had explained that he would like us to come out and replace his plug in his bathroom. When we arrived, we removed the bathroom plug, and we supplied and installed a new GFCI plug. We tested the new GFCI plug upon leaving and the plug was working correctly upon leaving.

We received a call from Ovid, Michigan the homeowner had explained that he would like us to come out and install a light fixture in the attic in his garage. When we arrived, we installed one new light fixture in the attic, we rewired lights to be controlled by a switch. We wired and installed a new switch at the bottom of the stairs. We tested the new light and switch upon leaving and both were working correctly.

We received a service call from Grand Ledge, Michigan the homeowner had explained that the vent fan in their bathroom was no longer working correctly. When we arrived we investigated the bathroom vent fan. We discovered that the fan did have the proper voltage and visually looked okay but the fan was all gummed up with dirt. We cleaned the bathroom vent fan and tested the vent fan. Upon leaving the vent fan was working correctly.

We received a call from Lansing, Michigan. The homeowner explained that he would like us to come out and service his riser. When we arrived we removed the old meter socket, and installed a new one. We removed the old riser pipe, and we installed a new riser pipe, new straps, new weather head, mew knob and new wire for the riser.  We tested the new meter socket and riser, upon leaving both were working correctly.

We received a call from DeWitt, Michigan. The homeowner had explained that he would like us to come out and install a plug for his generator. When we arrived we installed a plug, and wiring from the plug to the main panel. We installed generator breaker in the panel. We installed a new plug end on the existing cord. We tested the new generator plug and upon leaving the plug was working correctly.

We received a call from Lansing, Michigan. The owner had explained that he needed for us to come out and replace some breakers for him. We removed and replaced (1) 15amp GFCI Breaker. We removed, and replaced (10) single breakers. We removed and replaced (3) double breakers.

We received a call from Lansing, Michigan. The owner had explained that his power kept shutting off, and would like us to come and fix it. When we arrived we investigated why the circuits kept tripping. We found that the problem was that the circuits were being overloaded with the A/C units that were being plugged into them. We also discovered that the circuits must have been tripped too many times to cause the overheating issues that were caused in the panel. Two of the breakers needed to be replaced.We removed the old damaged breakers, we replaced the wire that was damaged from the heat in the panel. We supplied and installed two new breakers. We tested the new breakers and upon leaving the breakers were working correctly.

We received a call from Haslett, Michigan. The homeowner had explained that she needed her vent fan in her bathroom replaced. When we arrived we removed the existing vent fan, we assembled and installed a new vent fan. We installed new wiring into the new fan. Upon leaving we tested the new vent fan and the fan war working correctly.

We received a call from DeWitt, Michigan. The homeowner had explained that he would like us to come out and install a plug for his generator. When we arrived we installed the plug, we installed wiring from plug to main panel. We installed a new generator breaker in the existing panel. We supplied 1 10ft cord. We supplied and installed a interlock kit on the main panel. The interlock kit makes it so the main breaker and generator breaker cannot be on at the same time.

We received a call from Mason, Michigan.The homeowner explained that he would like us to come out and install 7 new plugs in his home. When we arrived we installed 20amp circuit for 5 plugs. We installed the wiring, and pipe for the new plugs. We then installed wire and piping for 2 15amp plugs. We tested the new plugs and upon leaving the 7 new plugs were working correctly.

We received a call from Mason, Michigan. The home owner had explained that he wanted us to come out and service his generator. When we arrived we replaced two spark plugs, the oil filter, air filter, and replaced the oil. We tested the battery and tested the generator and it was working correctly upon leaving.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he would like us to come Put new wiring into his barn. When we arrived we installed two new ground rods outside of the barn. We installed ground wire from rods to the panel, and installed wiring from house panel to barn wiring. We ran wiring through basement to outside junction box. We installed two new GFCI breakers in the barn panel to protect plugs in the barn.We installed circuit wiring for barn into the new panel. We labeled the breakers, and installed junction box covers and plates that are needed. We installed wiring underground from the home to the barn. We tested the wiring and new plugs. Upon leaving everything was working correctly.

We received a call from Pleasant Lake, Michigan. the homeowner had explained that she would like us to install a new sump pump circuit. When we arrived we installed a new dedicated 15amp circuit fir the sump in the crawl space. We installed a new tandem breaker in the panel to make room for new circuit. We installed new wire, box and GFCI plug in crawl space. We tested the new GFCI plug, and dedicated circuit, and both were working correctly upon us leaving.

We received a call from East Lansing, Michigan. The homeowner had explained that her range plug was no longer was working, and would like us to come out and fix it. When we arrived we investigated why the range plug was no longer working. We found neutral bar to be bad in panel. We moved the wires down to a good neutral bar location. We then tested the range plug and it was working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that he would like us to come out and service his riser. When we arrived, we removed the old service riser, wiring, broken meter hub. We installed a new meter hub, riser pipe, straps for the riser pipe, and riser wire. We connected the wiring in the meter. We tested the riser and upon leaving the riser was working correctly.

We received a service call from Lansing, Michigan. The homeowner explained that their outside lights were no longer working, and would like us to come take a look at them. When we arrived, we investigated the outside lights that were no longer working. We discover the problem was the connection was bad. We fixed the connection that was bad. Upon leaving we tested the lights, and they were working correctly.

We received a call from Lansing, Michigan. The owner had explained that their landscape light was not working correctly. When we arrived we investigated the light and discovered the bulb to be bad, and the wire connection was bad. We rewired the light to fix the problem. We also shortened the wiring by the transformer.

We received a call from East Lansing, Michigan. The homeowner had explained that he would like us to come out and correct his basement wiring. When we arrived we properly secured the wiring in the basement, We installed wiring up in the floor joist. We cleaned up the existing wiring to meet code. We tested the wiring and it was up to code upon leaving.

We received a service call from, Grand Ledge, Michigan. The homeowner was calling because the home only had half power. When we arrived we investigated the home, we tested electrical in home and found the problem to be with consumers power lines coming to the home. We informed the owner to contact consumers power to repair problems with power lines coming to home.

We received a call from Lansing, Michigan. The homeowner wanted us to come out and install an outdoor plug. When we arrived we installed a new plug by the backdoor. We put new wiring for a GFCI plug, and we installed a box and cover for the new plug. We tested the new plug and upon leaving the plug was working correctly.

We received a call from Albion, Michigan. The homeowner had explained that she would like us to come and install 6 new tamper proof plugs. When we arrived, we wired and installed 6 new tamper proof 15 amp plugs in the living room. We tested the new plugs and upon leaving all plugs were working correctly.

We received a call from Lansing, Michigan. The homeowner had explained that she would like us to come and install some vanity lights in her bathroom. When we arrived, we supplied and installed new mounting brackets. We then supplied, wired, and installed new vanity lights. We tested the new vanity lights and upon leaving the lights were working correctly.

We received a call from Lansing, Michigan. The homeowner had explained that they would like some duplex plugs removed. When we arrived we removed the old damaged duplex plugs. We supplied, and installed new brown outlets and plates. We tested the new plugs and they were working correctly upon leaving.

We received a call from Eaton Rapid, Michigan. The owner had explained that he would like some plugs removed and replaced. When we arrived we removed the old plugs, installed and tested new GFCI plugs. Upon leaving the new plugs were working correctly.

We received a call from Charlotte, Michigan. The homeowner had explained that he would like us to come out and service his riser. When we arrived, we removed the old damaged riser pipe. We installed a new riser pipe, new weather head, new straps and a new knob for the power lines. We connected the wiring to the meter. We tested the riser and everything was working correctly when leaving.

We received a call from Charlotte, Michigan. The homeowner had explain he would like us to come out and repair his meter that was no longer working correctly. When we arrived, we investigated the meter. The problem we discover was that the meter socket was bad and needed to be replaced. We installed the new meter socket, and connected wiring from the panel to the meter socket. We tested the meter and everything was working correctly when leaving.

We received a call from Okemos, Michigan. The owner had explained to us that he had old knob and tube wiring that he wanted us to remove. When we arrived to the home we installed (5) junction boxes to terminate and remove the knob and tube wiring. Also, we investigated the old wiring and found that what can be seen was in good working order and was safe now that we installed the junction boxes. We tested the new junction boxes and everything was working correctly when leaving.

We received a call from Okemos, Michigan. The owner had explained that half his kitchen plugs were not working, and would like us to come out and fix them. When we arrived we investigated why the plugs were not working. We discovered the problem to be a loose connection in the fridge plug. We connected the wires properly, and installed a new plug. We tested the circuit and everything was working correctly upon leaving.

We received a call from Lansing, Michigan. The owner had explained that he would like a plug moved and a new one installed for his A/C unit. When we arrived, we removed wiring that was running through the attic access. We installed new plugs and new wiring to reconnect wiring for the bedrooms. Also, we installed new plug for the built in A/C unit. We tested the new plugs and the plugs were working correctly.

We received a call from Lansing, Michigan. The homeowner had explained that he needed his riser serviced, and would like us to come out and service it. When we arrived we removed the riser pipe. We replaced the broken T.A. for the riser pipe, as well as the broken weather head. We installed a new riser pipe, we strapped the riser pipe and reinstalled the riser wire. We connected the wire to the meter, and we tested the riser and the riser was working correctly.

We received a service call from Lansing, Michigan. The homeowner had explained that he would like us to replace some of his existing plugs. When we arrived, we removed (4) of his existing plugs and replaced the plugs with new GFCI plugs that the owner had supplied. We tested the new GFCI plugs and the plugs were working correctly.

We received a call from Lansing, Michigan. The homeowner had explained that he would like us to come out and install a new vent fan. When we arrived, we removed the old damaged vent fan. We installed a new vent fan/light unit. We wired the fan and light so they would come on together.

We received a call from East Lansing, Michigan. The homeowner had explained that he would like us to come and install some plugs in his basement. When we arrived, we installed new wire from the plugs to constant power. We changed wiring in plug box to connect the new wire. The plugs are currently on with the basement lights (when lights are turned off the plugs go off). Upon leaving we tested the plugs and they were working correctly.

We received a call from East Lansing, Michigan. the homeowner had explained that he would like us to install a sump plug for his sump pump. When we arrived, we ran new wire to sump plug to make hot all the time. We reinstalled existing plug, then we tested the plug and found it to be working correctly.

We received a service call from Holt, Michigan. The homeowner had explained that his panel wasn't working correctly, and would like us to come take a look at it. When we arrived we discover that the panel wasn't working and the main breaker had gone bad. We supplied and installed a new breaker in the panel. We tested the panel and new breaker and they were working correctly.

We received a service call from Dimondale, Michigan. The homeowner had explained that he would like us to come out and repair his riser. When we arrived, we investigated the riser and discovered that the riser needed to be re-strapped to the riser. We re-strapped the riser pipe to the home correctly upon leaving.

We received a call from Okemos, Michigan. The homeowner had explained that he would like us to come install wiring for his TV in his living room. When we arrived, we installed the wiring for the tv. We mounted the tv on the wall. We installed a coax line for the television. We tested the connection upon leaving and the television was correctly wired and secure.

We received a call from Okemos, Michigan. The homeowner had explained that he would like us to come out and install 4 work bench plugs. When we arrived, We installed and wired the work bench plugs. We also installed and wired 1 new switch for the work bench plugs. Also, we installed a 4ft fluorescent light. We tested the new plugs and light and they were both working correctly.

We received a service call from Okemos, Michigan. The homeowner had explained that the house lost power, and she would like us to come out. When we arrived we investigated the house having no power. We found that the main breaker to be tripped. We tested the electrical and couldn't find any problems with the electrical system in the home. We reset the main breaker and tested homes electrical. We found everything to be working correctly.

We received a call from Dimondale, Michigan. The homeowner explained that he would like us to come out and wire his fireplace in his home. When we arrived, we installed 120 volt power for the new fireplace. We wired and connected the fireplace. We tested the new fireplace and it was working correctly upon leaving.

We received a call from Williamston, Michigan. The homeowner had explained to us that her ceiling fan needed to be rewired, and would like us to come out and re-wire it. When we arrived, we re-wired the wires in the ceiling fan box. We also supplied and installed a new dimmer switch for the light and fan. We tested the new dimmer switch and fan and both were working correctly upon leaving.

We received a call from Grand Ledge, Michigan. The homeowner had explained that she would like us to come out and install a generator plug for her generator. When we arrived, we installed a plug for the generator, we installed wiring from the plug to the main panel. We installed the plug inside the garage by the overhead door. We tested the new generator plug, and the plug was working correctly.

We received a call from Leslie, Michigan. The homeowner had explained to us that he needed a new dedicated circuit installed for his water heater, and that he would like us to install it. When we arrived we installed a new 30amp 240volt circuit from panel to water heater. We installed a new breaker in the panel for the water heater. Also, we installed a conduit pipe from the panel to the water heater. We wired in the water heater, then tested the circuit and breaker. Both the circuit and breaker were working correctly.

We received a call from Potterville, Michigan. The homeowner had explained that he would like us to come out and replace the horse water heater. When we arrived, we removed the old heat mat and sensor. We installed a new heat mat, and heat sensor. We tested both upon leaving and both were working correctly.

We received a call from Potterville, Michigan. The homeowner explained that he would like us to come install a welder plug. When we arrived we installed a welder plug above the panel in the tack room. We installed new wire, plug, and breaker. We tested the plug and found everything to be working correctly upon leaving.

We received a call from Potterville, Michigan. The homeowner had explained that he would like us to come take the old one out and put a new one in. When we arrived we removed the old unit, and we wired and installed the new water heater unit. We tested the new unit, and the water heater was working correctly upon leaving.

We received a call from Eaton Rapids, Michigan. The homeowner had explained that he would like us to come and replace the existing bathroom light. When we arrived we removed the existing light, and assembled and installed the new light that the customer had supplied. We tested the new light and eve thing was working correctly.

We received a call from Lansing, Michigan. The owner had explained that he would like us to come and fix the outside lights and plugs in the garage. When we arrived we removed the old wiring. We installed proper boxes for the light, and remounted and rewired lights. Also, we installed the proper wiring for garage plugs. We tested the wiring, plugs and lights and everything was working correctly.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he needed a GFCI plug installed for his washer plug, and would like us to come out and install one. When we arrived, we installed a new 20amp wire from the panel to the washer plug. We installed a new GFCI plug, and plate. We connected the wire to the existing laundry breaker in the panel. We left the existing laundry plug connected. We tested the new plug we installed and it was working correctly.

We received a call from Lansing, Michigan. The owner explained that he would like us to take a look at his circuit because it was no longer working. When we arrived, we investigated the circuit that was no longer working. We removed all the plugs and switches on circuit to trace down the problem. We removed the light fixture to trace down the problem, and traced the wiring throughout the home. The problem we discovered was the junction box had been left open and was not installed properly. We properly connected wiring inside the box and installed a cover. We tested the junction box and everything was working correctly.

We received a call from Okemos, Michigan. The homeowner had explained that she would like us to come out and install some new light switches. We installed a new switch on the main floor for the vanity lights. Also we installed a new switch in the upstairs bathroom for the vanity light. We tested the switch upon leaving and they were working correctly.

We received a call from Lake Odessa, Michigan. The homeowner had called and explained that his furnace was not working properly, and would like us to come out and fix it. When we arrived we investigated the old wiring by the furnace. We found a wire to be live, and the other seemed to be disconnected.  We disconnected a wire, and we installed 1 wire in the box and installed a GFCI plug. We tested the wiring and GFCI plug. Both were working correctly upon leaving.

We received a call from Dimondale, Michigan. The homeowner had explained that he would like us to come out and install a plug for his generator. When we arrived, we installed a 30amp 240volt generator plug in the garage. Also, we installed a new 30amp 4wire from the plug to the panel, and installed a new breaker in the panel for the generator. We installed a interlock kit in the panel. The interlock kit makes it so the main breaker and generator breaker cannot be on at the same time. We supplied a 50ft cord for the generator. We tested everything and everything was working correctly upon leaving.

We received a call from East Lansing, Michigan. The homeowner had explained that he would like us to come out and disconnect his phone lines. When we arrived we investigated the phone lines. We disconnected his old phone system in the home and tested the new phone line and connected to the phone line coming in home. When leaving phone line was working correctly.

We received a call from Grand Ledge, Michigan. The homeowner explained that he would like us to come out and service his riser. When we arrived, we removed the old damaged riser pipe. We installed a new hub, riser pipe, weather head, and new straps. We reinstalled the wiring for the riser. We tested the riser and everything was working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had called and explained that he would like us to come out and service his riser. When we arrived we discover that the riser pipe had been bent, so we bent it back to home. We installed new straps on the riser pipe, and a new knob to the home. We tested the riser, and upon leaving everything was working correctly.

We received a service call from Lansing, Michigan. The homeowner had called and explained that he would like us to come out and take a look at his old pump. When we arrived we investigated what was wrong, and found that the old wiring needed to be removed. We removed the old wiring and properly terminated it upon leaving.

We received a call from Grand Ledge, Michigan. The homeowner had explained that their doorbell no longer worked and would like us to come out and remove the old one and install a new one. When we arrived, we removed the old doorbell, and supplied and installed a new unit. We tested the new door bell and the door bell was working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that she would like us to install a new circuit in the panel for the water heater. When we arrived we installed a new circuit from the panel to the water heater location. We installed new surface mount pipe and box on the basement wall by the water heater. We installed new wiring and a GFCI plug for the water heater. Last, we installed a new breaker in panel for water heater. We tested the new plug and circuit, and everything was working correctly upon leaving.

We received a service call from DeWitt, Michigan. The homeowner had explained to us that his dryer was smoking and would like us to come out and fix it. When we arrived, we investigated the dryer and found the plug to be melted and improperly installed. The plug appeared to have been modified to make work with three wire system. We supplied and installed a new 3 wire dryer plug. We removed the old damaged plug and wiring. We fixed the wiring for the dryer. We tested the new plug and unit had correct voltage and wiring.

We received a call from Lansing, Michigan. The owner had explained that she wanted us to install a new circuit for her dryer. When we arrived, we installed a 30amp 4wire dedicated circuit, a 30amp 4 wire plug, a 30amp 4wire cord on the dryer, and a 30amp breaker in the panel for the dryer. We tested the new circuit and upon leaving everything was working correctly.

We received a call from Lansing, Michigan. The owner had explained that he would like us to come out and install a circuit for his range. When we arrived we installed a new 40amp 4wire dedicated circuit, a new 40amp 4wire plug, a new 40amp 4wire ford on the range. Also we installed a new 40amp breaker in the panel for the range. Upon leaving we tested the new circuit and it was working correctly.

We received a call from Mason, Michigan. The homeowner had explained that he would like a cable line installed. When we arrived we identified the location of the wiring that goes underground out to the driveway. We installed a flag and paint above the wiring location. We then installed a coax cable in PVC pipe going to the house.

We received a call from Okemos, Michigan. the homeowner had explained that he would like us to come out and repair his riser. When we arrived, we removed the damaged riser. We supplied and installed a new PVC riser. We installed 2 ground rods on the outside of the home. We installed ground wire from the rods to the panel.

We received a call from Okemos, Michigan. The homeowner had explained that he would like us to come out and repair his riser. When we arrived we re-secured the riser pipe to the home, and installed straps to the riser pipe.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he would like us to come out and install a new generator plug. When we arrived we installed a plug for the generator. We installed new wiring from the plug to the panel. We installed a generator breaker in the panel. We supplied a 25ft cord. We supplied and installed a interlock kit which makes sure that the main breaker and generator breaker don't run at the same time. We tested the new plug and it was working correctly upon leaving.

We received a call from Mason, Michigan. The homeowner explained that he wanted us to come out and install a circuit for his sun room. When we arrived we installed a new dedicated circuit from the panel to the sun room. We fished wire from their utility room to the right side of the sun room door. We fished wire from utility room to the panel. We supplied and installed a new breaker for the heat tile.

We received a service call from Lansing, Michigan. The homeowner had explained that they tried removing the light bulb and the end stayed in, and they couldn't get it out. Also, that their upstairs fan was loose. When we arrived we changed the socket in the ceiling fan light. We tightened the loose blade on the upstairs fan.

We received a service call from Lansing, Michigan. The homeowner had explained that they were trying to change out their lightbulb and the end got stuck in the socket and they could not remove it. Also, they had a fan that a blade was loose.When we arrived we installed a new socket for the light, and we tightened the loose blade on their fan upstairs.

We received a call from Williamston, Michigan. The homeowner had explained that she would like us to come out and repair her riser. When we arrived we removed the broken riser pipe, installed new PVC riser pipe, and straps. We disconnected the service wires, and installed a new weather head. We reinstalled service wires, and connected wiring in the meter socket. We tested the new riser, and riser was working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that she would like us to come out and move her dryer plug to a different location. When we arrived we moved dryer plug down the wall 10 feet. We reinstalled wire, piping, and the plug on the basement wall. We tested the plug. Everything was working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that she would like us to come out and service her riser. When we arrived we removed the damaged weather head, and installed a new weather head for service. We tested the weather head and was working correctly upon leaving.

We received a service call from Grand Ledge, Michigan. The homeowner had explained that their GFCI plug was no longer working. When we arrived we investigated the GFCI in the laundry room. We found it to be bad and needing to be replaced. We supplied and installed a new GFCI plug.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he would like us to come out and install a new duplex plug. When we arrived we removed the old 240volt range plug, and installed a new box and cover. And installed a new duplex plug. We tested the new plug and it was working correctly upon leaving.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he would like us to come out and install a 7500 Watt Manual Transfer Switch Panel. When we arrived we installed a 10 circuit transfer switch panel next to the panels in the basement. We transferred circuits from panel to the transfer panel. We installed a generator plug on the outside of the home by the basement doorway. We ran wire from the plug to the transfer panel. We supplied a 10ft cord to go from outside generator to the plug. We tested everything upon leaving and all was working correctly.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he would like us to come out and move some fluorescent strip lights. When we arrived we moved the lights from their existing location to a new location. We disconnected the wiring to move and reconnecting the wiring the light. We wired it so the lights would be controlled from existing wiring. We disposed of the old light fixtures in the garage. Upon leaving we tested the new light strip, and they were working correctly.

We received a service call from Williamston, Michigan. The homeowner explained that she would like us to come out and disconnect her security system. When we arrived we disconnected the security system for the home. We removed the battery and transformer that ran the security system.

We received a service call from Grand Ledge, Michigan. The homeowner had explained that they were having some problems with a light fixture and would like us to come out and fix it. When we arrived we investigated the breakers in the panel, and everything seemed to be working in its correct order. We found that a light fixture needed to be replaced, we removed the existing fixture and replaced and installed a new one. Everything was working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that she would like us to come out and service her riser. When we arrived we removed the old damaged meter socket, and installed a new one. We connected the wiring from the panel to the meter. We removed the old damaged riser pipe, and installed a new PVC riser with a weather head. We installed new straps, and new wiring for the riser. We tested everything upon leaving and it was working correctly.

We received a call from Okemos, Michigan. The homeowner had explained that he had some loose plugs. When we arrived we investigated the plugs and correctly secured the loose boxes to the wall.

We received a call from Eaton Rapids. The homeowner explained that he would like some lights installed for his garage. When we arrived, we wired, supplied and installed the lights. We tested the lights and they were working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that they would like us to come and replace their vent fan. When we arrived, we removed the existing vent van and ceiling light. We assembled and installed a new vent fan with a light. We wired in the new vent fan. We tested the new vent fan and light and both were working correctly upon leaving.

We received a call from Lansing, Michigan. The homeowner had explained that he would like us to come out and install a generator. When we arrived, we supplied and delivered a 1400 watt Generac generator. We supplied and installed a cold weather kit. We supplied and installed the generator battery. We installed a level pad and set the generator on the level pad. We installed wiring from the transfer switch panel to the generator. We installed a 16 space automatic transfer switch panel. We installed the transfer panel. We wired the transfer panel into the main panel. Also, we transferred the circuits from the main panel to the generator panel that will run off the generator. We tested everything upon leaving and all was working correctly.

We received a call from Lansing, Michigan. The homeowner had explained that she had a broken wire that she would like us to come out and fix. When we arrived, we repaired the broken wire in their basement rec room. We installed a junction box and new wire to repair the old wire.

We received a call from Okemos, Michigan. The homeowners explained that they would like us to come out and do an electrical inspection. When we arrived, we inspected the electrical throughout the home. We found everything to be in good working order.

We received a call from Okemos, Michigan. The homeowners had explained that they would like to have us come out and install some GFCI plugs. When we arrived, We removed the old duplex plugs, and supplied and installed (5) new GFCI plugs. We tested the new plugs for correct wiring and voltage. Upon leaving all plugs were working correctly.

We received a service call from East Lansing, Michigan. The homeowner had explained that he had a switch that was l=no longer working, and that he would like us to come out and fix it. When we arrived we investigated the switch and found that it was bad. We supplied and installed a new switch. We tested the switch upon leaving and it was working correctly.

We received a call from Lansing, Michigan. The owner had explained that they had a breaker that had gone bad and would like us to come out and replace it. When we arrived we removed the old breaker that had gone bad. We supplied and installed a new breaker. Upon leaving, we tested the new breaker and it was working correctly.

We received a call from East Lansing, Michigan. The homeowner had explained that he would like us to come out and install some flood lights. When we arrived, we removed the old existing light fixtures. We supplied and installed (3) head flood lights. We supplied and installed (3) new halogen flood bulbs. We tested the new flood lights upon leaving and they were all working correctly.

We received a call from Lansing, Michigan. the homeowners had explained that they wanted us to come out and replace some of their duplex plugs with GFCI plugs. When we arrived we removed the old duplex plugs, and supplied and installed new GFCI plugs and plates. We tested the new plugs and upon leaving plugs were working correctly.

We received a call from Lansing, Michigan. The owner had explained that he would like us to come out and install a vanity light. When we arrived, we removed the old light from the medicine cabinet, and installed a new box. We installed a keyless light fixture on the box. We also installed a new GFCI plug. We tested the new light fixture and plug and both were working correctly upon leaving.

We received a service call from Lansing, Michigan. The homeowner had explained that he had no power to parts of his home. When we arrived we investigated the parts of the home that had no power. We found the problem to be that there was a breaker that had been tripped. We reset and re-tested the breaker and everything was working correctly.

We received a call from Grand Ledge, Michigan. The homeowner had explained that he believed something was wrong with the breaker. When we arrived we investigated the main breaker and found the problem to be that the main breaker had gone bad. We supplied and installed a new breaker and upon leaving the main breaker was working correctly.

We received a call from Grand Ledge, Michigan. The owner had explained that he would like us to come out and install a new 240volt plug for his generator. When we arrived we installed new wiring from the junction box in the basement to a new range plug. We supplied and installed a new range plug. We tested plug for range. We supplied and installed range cord on the range. We tested the new range plug upon leaving and the plug was working correctly.

We received a call from Grand Ledge, Michigan. The owner had explained that the dishwasher was no longer working and would like us to come out and fix it. When we arrived, we investigated why the dishwasher was not working, we found that the wire connections behind the dishwasher to be improper and had gone bad. We properly installed the wiring to the dishwasher. We tested the dishwasher, and everything was working correctly when leaving.

We received a call from Lansing, Michigan. The homeowner explained that they would like us to come out and repair their riser. When we arrived we fixed the broken pipe. We installed the pipe back up on the house, and rest rapped the pipe to the house upon leaving.

We received a call from DeWitt, Michigan. The homeowner explained that their breakers kept tripping. When we arrived, we investigated the tripped breakers, and found that the circuits were overloaded. We also found that the kitchen had two circuits tied together under the breaker. We moved the toaster in the kitchen and told the homeowners to move the heater in their basement and that should correct the overload issue.

We received a call from Grand Ledge, Michigan. The owner had explained that he would like us to install an interlock kit on his main panel. When we arrived we installed wiring from the panel to the generator plug outside. We installed a 30amp generator breaker. We supplied and installed a 30amp generator plug. We supplied and installed an interlock kit for the main panel. The interlock kit makes it so the main breaker and the generator breaker cannot be on at the same time.

We received a service call from Charlotte, Michigan. The owner had explained that she would like us to come out and check the load on the appliances. When we arrived we investigated the energy consumption. We found that the electrical to be in good working order. We tested for proper voltage, we checked the wires in the panel and found everything to be in proper order. We did however find that the hot tub seemed to be running almost all of the time which has high energy consumption.

We received a call from Grand Ledge, Michigan. The homeowner had called and explained that he would like us to disconnect his old hot tub, and wire in a new one. When we arrived, we removed the wiring to the existing hot tub. We tested the wiring and found it to be working correctly. We installed the existing wire into the new hot tub. We installed straps on conduit for the tub. We tested the voltage to the hot tub. We could not completely test the hot tub due to the fact that there was no water in the hot tub.

We received a call from Eaton Rapids, Michigan. The caller explained that they wanted us to come out and install a motion light outside. When we arrived we wired and installed a new motion light for the side of the home. We wired and installed a new switch on the left side of the doorway. We supplied the motion light and light bulbs. We tested the motion light, and the light was working correctly upon leaving.

We received a service call from Lansing, Michigan. The homeowner had explained that the circuit was no longer working. When we arrived we investigated why the circuit was no longer working. We found the breaker to have been tripped. We reset the breaker, then tested the circuit and everything was working correctly upon leaving.

We received a call from Lansing, Michigan. The caller had explained that she would like us to come out and replace the existing outdoor plugs. When we arrived, we removed the (4) existing outdoor plugs. We supplied and installed (4) new GFCI plugs and covers. We then tested the plugs and everything was working correctly upon leaving.

We received a call from Grand Ledge, Michigan. The caller had explained that their Kitchen plugs were not working, and would like us to come fix the problem. When we arrived we investigated the kitchen plugs. We found that The GFCI plug to the right of the sink to have gone bad and needed to be replaced. We removed the existing plug and plate. We supplied and installed a new GFCI plug and plate.

We received a call from Lansing, Michigan. The called had explained that he would like us to come out and upgrade his service. When we arrived we removed the old service riser, wiring, old meter and panel. We supplied and installed new PVC riser pipe and wire. We installed a new meter socket, and new wiring from the meter to the panel. We supplied and installed a new 200amp 40 space panel. We supplied and installed new breakers for the panel. We then labeled the breakers in the panel. We reinstalled wiring for the home in the new panel. We then tested the new panel and breakers and everything was working correctly upon leaving.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and service his riser. When we arrived we removed the old damaged meter socket, and installed a new one. We installed a new riser pipe and weather head, and strapped the riser pipe. We installed wiring in the riser pipe. We connected the wiring in the meter socket. We installed a new knob for the power company. We tested everything upon leaving and everything was working correctly.

We received a call from Lansing, Michigan. The caller had explained that she would like us to come out and service her riser. When we arrived we removed the old riser pipe, and disconnected service wires. We installed a new hub on the meter socket. We installed new PVC riser pipe and straps. We then reinstalled service wires, reconnecting the power line.

We received a call from Lansing, Michigan. The caller explained that he would like us to come out and install a dryer plug. When we arrived we supplied and installed a new dryer plug. Also we supplied and installed a breaker in the panel for the new plug. We tested the new plug upon leaving and the plug was working correctly

We received a call from Lansing, Michigan. The caller explained that she would like us to come out and remove and replace her dimmer. When we arrived we removed the old, broken dimmer. We supplied and installed a new dimmer. Upon leaving we tested the new dimmer and everything was working correctly.

We received a call from Lansing, Michigan. The caller explained that they had a plug that was no longer working. When we arrived, we investigated the plug that was no longer working. We discovered that the plug was bad and needed to be replaced. We removed the bad plug, and supplied and installed a new GFI plug. We tested the new plug upon leaving and the plug was working correctly.

We received a call from Grand Ledge, Michigan. The caller had explained that some of his plugs were no longer working. When we arrived we investigated the plugs that were not working. We discover the problem to be that the GFCI plug was tripped. We reset the GFCI plug and then tested the plugs upon leaving and the plugs were working correctly.

We received a call from Eagle, Michigan. The caller called and explained that he would like us to come out and install some breaker blanks. When we arrived we supplied and installed blank breakers in the panel. We tested the new breakers upon leaving and everything was working correctly.

We received a call from Lansing, Michigan. The caller explained that he would like us to install a GFI plug for the water heater. When we arrived we supplied and installed the new GFI plug for the water heater. Then we tested the plug upon leaving and the plug was working correctly.

We received a call from Grand Ledge, Michigan. The owner had explained that he would like us to come out and do yearly maintenance on his generator. When we arrived, we replaced the spark plugs, air filter and oil in the unit. We tested the generator for proper operation and voltage upon leaving and everything was working in its correct order.

We received a call from Williamston, Michigan. The caller had explained that he would like us to come install a plug for his generator. When we arrived, we installed a plug for the generator. We installed wiring from the plug to the main panel. Also we installed a generator breaker in the panel.

We received a call from Williamston, Michigan. The caller had explained that she would like us to come in and install a phone line. When we arrived we ran (1) CAT5e line from the new office area to the server location. We installed a data plate in the new office. We installed a wall phone plate. We tested everything upon leaving and it was working correctly.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and install a new plug for his TV. When we arrived we fished in new wiring, installed a new plug, and plate. We then wired the new plug, and tested the plug upon leaving and everything was working in the correct order.

We received a service call from Mulliken, Michigan. The caller had explained that she was getting shocked by a plug and would like us to come out and see why. When we arrived we investigated the voltage on the side of the porch. We found the metal railing to have 120volts running through it. We traced the problem to switches at the front door. We moved the wiring in three gang at the front door. The problem seemed to be inside the wall by the front door. We explained to the owner that if the problem came back we would have to open up the wall to fix it properly.

We received a call from Okemos, Michigan. The caller had explained that she would like us to come out and install vanity lights in their master bathroom.  When we arrived we removed and replaced the vanity lights that the owner had supplied us with. We then tested the new vanity lights upon leaving and the lights were working correctly.

We received a call from Dimondale, Michigan. The caller had explained that he would like us to come our and replace his current ceiling fan in his living room. When we arrived, we removed the existing ceiling light box and wiring, and installed a new ceiling box for the fan. We texted the new ceiling fan upon leaving and it was working correctly.

We received a call from Grand Ledge, Michigan. The homeowner explained he would like us to come out and install a plug for his generator. When we arrived we installed the plug. We installed wiring from the plug to the main panel. We also installed a generator breaker in the panel. We tested the new plug upon leaving and the plug was working correctly.

We received a call from Charlotte, Michigan. The caller had explained that they would like us to come out and install a generator plug for them. When we arrived we installed the plug for the generator. We installed wiring from the plug to the main panel, and installed a generator breaker in the panel. We installed the plug by the garage service door. Upon leaving we tested the new plug and the plug was working correctly.

We received a call from Mulliken, Michigan. The caller had explained that she would like us to come out and install a plug for her generator. When we arrived we installed the plug for the generator and installed wiring from the plug to the main panel, and installed a breaker for the generator in the panel. We supplied a 25ft cord for the generator. We tested the plug and cord upon leaving and the plug and cord were working correctly.

We received a call from Lansing, Michigan. The caller had explained that he would like us to change the bulbs on his light fixtures as well as test them. When we arrived we changed out the light bulbs with the bulbs that the owner had supplied. Upon leaving we tested the light fixtures and they were all in correct working order.

We received a service call from Lansing, Michigan. The caller had explained that he had a light fixture that was no longer working correctly. When we arrived we investigated the light fixture. We discovered that the bulb was bad. We replaced the bulb and then re tested the fixture upon leaving and everything was working in its correct order.

We received a service call from Lansing, Michigan. The caller explained that he had two broken bulbs in his light fixture that he could not remove. When we arrived we removed the two broken bulbs and supplied and replaced the bulbs. We tested the light fixture upon leaving and the fixture was working in correct order.

We received a call from Eagle, Michigan. The caller had explained that he would like us to come out and install a new outdoor farm light. When we arrived we removed the old farm light on the barn. We supplied and installed a new fluorescent light fixture. We tested the new light fixture upon leaving and the light was working in the correct order.

We received a call from Eagle, Michigan. The caller had explained that he would like us to come out and install a generator plug. When we arrived we installed the plug. We installed wiring from the new plug to the panel, and we installed a generator breaker in the main panel. We then tested the plug upon leaving and the plug was working in correct order.

We received a call from Charlotte, Michigan. The caller had explained that he would like us to come out and wire his control box. When we arrived we installed (2) new dedicated circuits to the control box. We installed wiring from the sub-panel to the control box. We installed new breakers for new circuit. We wired high voltage in the control box.

We received a call from Mulliken, Michigan. The caller had explained that he would like us to come out and install some outdoor plugs. When we arrived we wired and installed the box, plug and covers. We tested the new outdoor plugs upon leaving and everything was working in it correct order.

We received a call from Grand Ledge, Michigan. The caller explained that she would like us to come out and service her riser. When we arrived we removed the old damaged meter socket, and installed a new one. We connected the wiring from the panel to the new meter. We also removed the old damaged riser pipe and wire, we installed a new riser pipe and weather head, and new wiring for the riser. We connected the wiring into the meter. Lastly, we installed nob on the riser for the power company. We tested everything upon leaving and it was in its correct working order.

We received a call from Lansing, Michigan. The caller had explained that they would like us to come out and install a plug for their generator. When we arrived we installed the plug. We installed wiring from the plug to the main panel, and installed a breaker in the panel. We then tested the plug and the plug was working correctly.

We received a service call from East Lansing, Michigan. The caller had explained that they had a plug in their garage that was no longer working. When we arrived we investigated the GFCI plug in the garage that was no longer working. We had discovered the plug to have gone bad, and it needed to be replaced. We removed the p;d bad GFCI plug and supplied and installed a new one.

We received a service call from DeWitt, Michigan. The caller had explained that the bathroom, garage, and outside plugs were no longer working. We discover the problem to be a bad plug in the master bathroom that was not letting the electricity flow to the rest of the plugs. We removed the bad duplex plug, and supplied and replaced it with a new plug. Upon leaving we tested the new plugs and they were working in correct order.

We received a call from DeWitt, Michigan. The homeowner had explained that there would like us to come out and install a post light switch. When we arrived we installed a junction box in the basement for the post light. We removed the existing time clock. We installed new wire from the junction box to the new switch. We installed the new switch on the first floor. We supplied and installed the switch. Upon leaving we tested the post light and it was in correct working order.

We received a call from Grand Ledge, Michigan. The caller explained that she would like us to come out and service her riser. When we arrived we installed a new meter, and installed new wiring from the panel to the meter. We installed a new riser pipe, weather head, knob, and new wiring in the riser pipe. We then tested the new riser pipe, and it was in correct working order.

We received a call from Lansing, Michigan. The owner had explained that she would like us to come out and install a range plug. When we arrived, we removed the existing surface mount range plug, we cut in a new range plug in the wall. We rerouted the wiring into a new range box, and we supplied and installed a new range plug. We tested the new range plug upon leaving, and the plug was working correctly.

We received a service call from Grand Ledge, Michigan. The caller had explained that she had a fan that was no longer working. When we arrived we investigated the fan that was no longer working. We found that the wiring was not properly installed and had come loose. We installed a junction box in the attic, and properly installed the wiring in the junction box. We tested the fan and the unit was working correctly.

We received a call from Grand Ledge, Michigan. The caller had explained that she would like us to install a generator for her home. When we arrived we supplied and delivered a 10,000WATT Generac generator. We supplied and installed a cold weather kit. We supplied and installed a new generator battery. We installed a level pad for the generator to set the generator on. We installed wiring from the transfer switch to the generator, also installing control wiring from generator to transfer switch. We supplied and delivered (1) 16 space automatic transfer switch panel. We installed the transfer panel and wired the transfer panel into the main panel. Upon leaving we tested the new generator and everything was working in its correct order.

We received a call from Lansing, Michigan. The owner called and explained that they would like us to come out and install a plug for their fireplace. When we arrived we installed a new plug under the mantle for the rope light. We wired in the new plug, supplying and installing a new plug and plate. We tested the new plug upon leaving and the plug was working correctly.

We received a call from Lansing, Michigan. The caller had explained that they had a post light that had stopped working. When we arrived, we investigated the post light that was no longer working. We found that the ballast and bulb to be bad. We supplied and installed a new ballast and bulb, then tested the post light, and it was working in its correct order.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and wire/install 2 plugs. When we arrived, We installed a new box, wire, GFCI plug and plate. We tested the plugs upon leaving and they were in correct working order.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and install a plug for his generator. When we arrived we installed the plug for the generator, we installed wiring from

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and install a plug for his generator. When we arrived we installed the new plug, We installed wiring from the plug to the panel, and installed a generator breaker in the panel. We tested the plug upon leaving and the plug was working correctly.

We received a call from Lansing, Michigan. The caller explained that he would like us to come out and replace his carbon/smoke detectors. When we arrived we replaced the upstairs hallway smoke with a combo unit. We replaced the basement utility room smoke also with a combo unit. We tested the units that we installed upon leaving and they were working correctly.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and install a usb charger plug. When we arrived we supplied and installed a usb charger plug. We also supplied and installed a plate for the plug. We tested the new plug upon leaving and the plug was working correctly.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and replace the old post and light. When we arrived we removed the old post and light. We supplied and installed a new pvc post. We supplied and installed a new GFCI plug and plate, and supplied and installed a new LED flag light. Upon leaving we tested the new light and post and both were in proper working order.

We received a call from Lansing, Michigan. The owner had called and explained that he would like us to come out and install a dedicated circuit for his water heater. When we arrived we installed a new dedicated circuit from the panel to the new water heater. We supplied and installed a new 30 amp breaker for the water heater. We wired in the new water heater.We tested the new wiring and circuit. everything was in correct working order when leaving.

We received a service call from Grand LEdge, Michigan. The caller has explained that he had some damaged wiring that he had noticed and would like us to come out and fix it. When we arrived we repaired two damaged 12-2 romex wires, and one damaged phone line. We then tested the repaired wiring. And everything was in proper working order upon leaving.

We received a call from Lansing, Michigan. The homeowner explained that he would like us to install a circuit for his sewage pimp system. When we arrived we install a new circuit and wiring, and tested the wiring and circuit upon leaving and both were in proper working order upon leaving.

We received a call from Lansing, Michigan. The owner had called and explained that he would like us to come out and wire in his electric water heater. When we arrived we installed a dedicated 20amp circuit, and a new breaker in the panel, also a breaker lock. We installed the new wiring and wired in the water heater. Upon leaving we tested the new wiring, breakers and circuits and everything was in proper order upon leaving.

We received a call from Lansing, Michigan. The caller has explained that his dishwasher was no longer working. When we got there we investigated the dishwasher. We discover that a wire had been broken. We repaired and re-tested the dishwasher wiring and the wiring was in correct order upon leaving.

We received a call from Lansing, Michigan. The caller has explained that his dishwasher was no longer working. When we got there we investigated the dishwasher. We discover that a wire had been broken. We repaired and re-tested the dishwasher wiring and the wiring was in correct order upon leaving.

We received a call from Grand Ledge, Michigan the caller had explained that he would like us to come out and replace his knob and tube wiring. When we arrived we removed the knob and tube wiring in the attic. We replaced the knob and tube wiring with romex wiring. We installed junction boxes in order to remove the knob and tube wiring.

We received a call from East Lansing, Michigan. The caller had explained that he would like us to come out and install a plug for his generator. When we arrived we installed the plug. We installed wiring from the plug to the panel, and installed a generator breaker in the panel. We tested the plug and it was in proper working order.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and repair his riser. When we arrived, we removed the damaged riser pipe, and installed a new pvc riser pipe and straps. We connected riser wires in the meter socket.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and replace his door heel unit. When we arrived we removed the existing door bell unit on the first floor and installed a new unit in the basement. We supplied the new door bell unit for the basement. The customer supplied the door bell unit for the first floor and we installed it. We installed the door bell unit on the outside by the front door. We then tested the door bell units, upon leaving and the units were working in their proper order.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and install a grounding junction box. When we arrived we installed the grounding bar, and connected grounds for the basement junction box. We screwed the old panel door shut.

We received a service call from Lansing, Michigan. The caller had explained that the lighting outside was no longer working. When we arrived we investigated why the breaker wouldn't reset for the outside lighting. We discovered that the wiring going to one set of lights appeared to be damaged and needed to be repaired. We disconnected one set of lights and the remainder of the lights were working correctly

We received a call from Lansing, Michigan. The caller had explained that she would like us to come out and replace their existing ceiling fan. When we arrived we removed the existing ceiling light, we assembled and installed a new ceiling fan. We tested the ceiling fan upon leaving, and the fan was in correct working order.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and repair his riser. When we arrived we removed the old damaged riser pipe, wiring, and broken meter hub. We installed a new meter hub, riser pipe and wiring. We then strapped the riser to the home. We tested everything upon leaving and everything was in its correct working order.

We received a call from Okemos, Michigan. The caller explained that she wanted us to come out and install some cane in her living room. When we arrived we supplied and installed (4) 6' recess cans. We wired and installed a new switch for the recess cans. We then tested the switch and cans upon leaving and they were all in proper working order.

We received a call from Grand Ledge, Michigan. The caller had explained that he wanted us to come out and repair his riser. When we arrived we removed the old damaged riser, and disconnected the wire from the meter. We installed new riser wire, and strapped the new riser wire. We connected the riser wore to the meter, and installed a new weather head. We tested the new wiring and upon leaving everything was in its correct order.

We received a call from Haslett, Michigan. The called had explained that he would like us to come out and install a new plug for the generator. When we arrived we installed the plug, and wiring from the plug to the panel. We installed a generator breaker in the panel. We installed the plug by the A/C unit by the garage. We tested the plug and wiring upon leaving and it was in the proper working order.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and repair her riser pipe. When we arrived we installed a new hub for the meter socket, and reinstalled the riser pipe and straps. Lastly we reinstalled wiring for the riser. We then tested the Riser and it was in correct working order upon leaving.

We received a service call from East Lansing, Michigan. The home owner had called and explained that their furnace was no longer working. When we arrived we investigated the furnace. We found the furnace to be getting the correct voltage but the unit still would not run. The electrical board may have gotten wet. We investigated the 2nd floor not working. We found the breaker to have been tripped. We rest the breaker and the circuit worked for a couple of minutes until it tripped again. We informed the owner to dry the house out and we would then return and see if the circuit still is not working correctly/

We received a call from Lansing, Michigan. The owner had explained that she would like us to come out and install a breaker for her dryer . When we arrived we removed the old 50amp breaker that was on the dryer. We supplied and installed a new 30amp breaker for the dryer. We supplied and installed a new 30 amp dryer cord.

We received a call from Lansing, Michigan. The owner had called and explained that he would like us to come out and install wiring to a bathroom vent fan. When we arrived we installed a new switch for the vent fan, and wired from the new switch to the vent fan.

We received a call from DeWitt, Michigan. The caller had explained that he wanted us to come out and service his riser. When we arrived we removed the old damaged riser pipe,and damaged meter hub. We installed a new meter hub, riser pipe, weather head, and riser straps. We installed a new knob for the power lines, and reinstalled the service wire. Lastly, we connected the wires in the meter socket.

We received a service call from Grand Ledge, Michigan. The caller had explained that his oven was not working and would like us to come out and fix it. When we arrived we investigated the oven that was not working. We discovered the switch to be bad, so we bypassed the switch that way the oven would work.

We received a service call from DeWitt, Michigan. The owner had called and explained that they had a plug no longer working. When we arrived we investigated the plug. We found the problem to be that water had been sprayed on the GFCI plug, which had caused the plug to go bad, and needed to be replaced.We Let the owner know that the water leak needed to be repaired by a plumber so the problems didn't continue. To fix the plug we removed the bad GFCI plug and plate, and supplied and installed a new plug and plate. We tested the new plug upon leaving and it was working in the correct order.

We received a call from Lansing, Michigan. The caller had explained that she would like us to come out and install a new plug in her bathroom. When we arrived, we installed new wiring and a box under vanity light for a new plug. We supplied and installed a new GFCI plug and plate. We also installed a plug on the second floor bathroom. We removed the existing GFCI plug and installed a new double box, and a new GFCI plug and plate. We tested the new plugs and they were working in proper order.

We received a call from Lansing, Michigan. The caller had explained that he thought there was water damage to his panel. When we arrived, we investigated the panel for water damage. We discovered a lot of water inside of the panel. We disconnected the power to the panel, and removed breakers in the panel so the tub could be dried out. We reinstalled the breakers after the tub was dried out. We cleaned the main lugs on the panel, and tested the breakers and all of them were working correctly after re-energizing.

We received a call from Lansing, Michigan. The caller explained that she would like us to come out and replace her vent fan. When we arrived, we removed the old vent fan. We wired and installed a new vent fan, and replaced the switch and plate. We tested the new vent fan, and switch and both were working correctly.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and install wiring for A/C. When we arrived, we corrected the existing wiring for the A/C unit. We installed a new disconnect and whip, and tested the circuit. We installed a new dedicated 30amp 240volt circuit for the A/C unit. We installed a new breaker in the panel for the A/C, and installed a new disconnect and whip. Lastly, we tested that circuit.

We received a call from Lansing, Michigan. The caller had explained that he would like us to come out and install a surge suppressor. When we arrived, we supplied, wired, and installed a new surge suppressor in the panel. We then tested the surge suppressor and it was working correctly.

We received a call from DeWitt, Michigan. The caller had explained that he would like us to come out and install a Dedicated circuit for his water pump. When we arrived, we installed a dedicated line from the basement, to the outside of the building. We installed a new GFCI plug on the outside of the home, and installed a new breaker in the panel. We then tested everything, and it was in the proper working order.

We received a call from Okemos, Michigan. The caller had explained that he would like us to come out and install a circuit extension for his living room. When we arrived, we installed new wiring from an existing plug to a new plug. We installed a new box, plug, and plate, then tested it. Upon leaving the plug was in the proper working order.

We received a call from Grand Ledge, Michigan. The caller had explained that he wanted us to come out and install a sub-panel. When we arrived we installed a 20 space sub-panel next to his main panel. We installed a breaker in the main panel to feed the sub-panel. We wired from the main panel to the sub-panel, and wired the dryer into the new panel to make room for the sub-panel breaker. We tested the sub-panel, and it was in proper order upon leaving.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to re-wire his garage. When we arrived we reinstalled wiring from the house to the garage, and install new knob on garage for wire. We reconnected the wiring going into the garage, and reconnected the wiring for the switch in the garage.

Electrical Service Call

We received a call from DeWitt, Michigan. The caller had explained that he would like us to install a new panel in his basement. When we arrived we removed the old panels in the basement. We installed 30space 100amp panel, and installed old wiring for house in the new panel. We installed new breakers in the panel for house circuits, and labeled the new panel. We then tested the new breakers and panel and they were in the correct working order.

We received a call from DeWitt, Michigan. The caller had explained that she would like us to come out and install a circuit for her dishwasher. When we arrived we installed a new dedicated 15amp circuit for the new dishwasher. We ran wire from the dishwasher to the panel, and wired in the dishwasher. We then tested the circuit and the dishwasher and they were in the correct working order.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and service his overhead. When we arrived we removed the old 100amp service riser and wire, and installed a new 200amp service and wire. We removed the old meter socket, and installed a new one. We removed the old 100amp fuse panel, and supplied and installed a new 200amp 40 space panel. We installed and labeled new breakers, and installed ground rods on the outside of the home and connected them to the panel. We installed bonding wire to the water lines in the home, and installed boding wire to the gas line in the home. Lastly, we installed a junction box for the well pump wire, We tested everything upon leaving, everything was in correct working order.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and service his overhead. When we arrived we removed the old 100amp service riser, and wire and installed a new 200amp service riser and wire. We removed the old meter socket, and installed a new one. We removed the old 100amp fuse panel, and installed a new 200amp 40 space panel. We installed and labeled the breakers. We installed ground rods on the outside and connected it to the panel. We installed bonding wire to the water lines in the home. We installed bonding wire to the gas line in the home. Lastly we installed a junction box for the well pump wire. We tested everything upon leaving, and everything was in correct working order.

We received a call from Portland, Michigan. The caller had explained that his phone system was not working correctly and thought it could be an electrical problem, and his sauna was not working correctly and would like us to diagnose the problem. When we arrived we investigated the phone system. We discovered that the system was bad and needed to be replaced. We tied the phone line together to bypass phone system so the phones would work. We investigated the sauna, and discover that the heating elements for the sauna had gone bad and needed to be replaced.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and install a new circuit for his dishwasher. When we arrived, we ran a new circuit from the panel to the dishwasher. We wired in the dishwasher, and installed a new breaker lock in the panel to the dishwasher. We tested the new circuit and the circuit was in correct working order upon leaving.

We received a call from Potterville, Michigan. The caller had explained that she would like us to come out and install a cold weather kit and do a yearly service on her generator. When we arrived we supplied and installed the cold weather kit. We replaced the spark plugs, oil filter, air filter, oil and load tested the battery for the generator. We tested for proper operation and voltage.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and wire in a vent fan/light. When we arrived we wired and installed the vent fan. We tested the vent fan/light upon leaving and it was working in proper order.

We received a call from East Lansing, Michigan. The home owner called and explained that he would like us to come out and install a new circuit for his dryer. When we arrived we installed a new circuit from the panel to the dryer location. We installed a new GFCI plug. We installed a new wire, pipe and box. We tested the new circuit and it was working correctly upon leaving.

We received a service call from Grosse Point Farm, Michigan. The owner had called and explained that she would like us to come out and investigate why the bathroom plugs were no longer working. When we arrived we found a breaker, and GFCI plug to also have gone bad. We removed the bad breaker and GFCI plug, and supplied, and installed a new breaker and new tamper proof GFCI plug. We then tested the new breaker and plug, and both were working correctly upon leaving.

We received a service call from Lansing, Michigan. The caller had explained that he wanted us to come out and wire in his fireplace. When we arrived we installed wiring for the fireplace in the panel, and connected the wiring into the breaker. We then tested the wiring upon leaving, and it was in correct working order.

We received a service call from East Lansing, Michigan. The caller had explained that he would like us to come out and see why his breaker kept tripping. When we arrived we investigated the breaker that kept tripping in his main panel. We found the breaker to be double fed, we removed the wire from the breaker and capped it off in the panel.

We received a call from Ann Arbor, Michigan. The caller had explained that they would like us to come out and install a flood light. When we arrived we installed a new switch inside the garage for the new light. We installed a double head flood light in soffit by the garage door, and wired in the new light.

We received a call from Grand Ledge, Michigan. The caller had explained that he wanted us to come out and look at his generator that wasn't working correctly. When we arrived we discover that his capacitor needed to be replaced. We removed the old one and supplied and installed a new one.

We received a call from East Lansing, Michigan. The caller had explained that he would like us to come out and install heat tape on his roof. When we arrived we supplied and installed heat tape for the south side of the back of the house roof. We looped heat tape the first 2-3 ft of the roof line. We installed heat tape in the gutters and in the downspout. We tested the system and wired the system from existing circuit and switch inside the house.

We received a call from Grand Ledge, Michigan. The homeowner had called and explained that he wanted us to come our and maintenance his generator. When we arried we changed the spark plug, oil filter, oil and tested the unit upon leaving.

We received a call from Grand Ledge, Michigan. The caller had explained that he would like us to come out and replace the battery in his generator. When we arrived we removed the old battery, and supplied and installed a new one. We tested the new battery upon leaving and everything was working in its proper order.

We received a call from Lansing, Michigan. The homeowner had called and explained that he would like us to come out and install a new circuit. When we arrived we installed a new circuit from the panel to the junction box in the crawl space. We installed a new junction box to connect the new circuit to wiring going to light fixtures. We installed a new breaker in the panel to power outside lights.

We received a call from East Lansing, Michigan. The homeowner had called and explained that his outdoor plugs were no longer working, and would like us to come out and fix the problem. When we arrived we found that (1) GFCI plug had gone bad, and that too many lights to be on the circuit outside for breaker to stay on. We reset the breakers, and removed several lights from the circuit.

We received a call from Gladstone, Michigan. The caller had explained that the two outside lights and porch light was not working correctly. We discover rgar the photo eye that controlled the outside lights were installed improperly. We bypassed the photo eye so the lights were only controlled by the wall switch. We tested the lights and all were working in the correct order upon leaving.

We received a call from Lansing, Michigan. the owner had explained that she would like us to come out and look

We received a call from East Lansing, Michigan. The homeowner explained that he wanted us to come out and install a plug for his new gas dryer. When we arrived we installed a new circuit from the panel to the dryer location. We installed a new GFCI plug, and installed new wire, pipe and a box. We tested the new circuit and it was working in its correct order upon leaving.

We received a call from Grand Ledge, Michigan. The called had explained that he would like us to come out and install a circuit for his sign. When we arrived we installed a new 20amp circuit from the panel to the outside junction box with photo eye. We installed a new 20amp breaker in the panel for the sign, and wired in a new circuit into the photo eye and reinstalled the cover. We tested the wiring going underground to the sign and tested the sign after final wiring.

We received a call from Grand Ledge, Michigan. The owner had called and explained that he wanted us to come out and replace a light that was on the outside of his building. When we arrived we removed the old light fixture for the parking lot. We supplied and installed a new 250watt Metal Halide light fixture. We tested the new light apron leaving and the light was in correct working order.

We received a call from Grand Ledge, Michigan. The homeowner explained that he would like us to come out and replace some GFCI plugs in his house for him. When we arrived we removed the old plug, and installed the new GFCI plugs and installed 2" screws. We then tested the new outlets and they were in correct working order upon leaving.

We received a call from Grand Ledge, Michigan. The homeowner explained that he wanted us to come out and replace a switch for him. When we arrived we removed the old switch, and installed a new switch. We installed a box extension for the box, and installed 2" screws. We tested the switch upon leaving and the switch was working in it correct order.

We received a call from Grand Ledge, Michigan. The homeowner explained that he wanted us to come out and replace a switch for him. When we arrived we removed the old switch, and installed a new switch. We installed a box extension for the box, and installed 2" screws. We tested the switch upon leaving and the switch was working in it correct order.

We received a call from Grand Ledge, Michigan. The caller explained that she wanted us to come out and rewire a plug box in her home. When we arrived we rewired the plug box, and tested it upon leaving and the plug was in the correct working order upon leaving.

We received a call from Lansing, Michigan. The owner had called and explained that he wanted us to come out and fix his dawn/dusk lights. When we arrived, we removed the existing wiring and piping that went to the light due to it not being legal. We supplied and installed proper piping and wiring going to the lights. We rewired the lights to constant circuit so the lights are on with the entry lights. We tested the lights upon leaving and they were in correct working order.

We received a call from Okemos, Michigan. The owner had explained that he would like us to come replace his outdoor lighting with new LED lighting. When we arrived, we removed the old outdoor lighting, and supplied and installed new LED outdoor lighting. We tested the new lighting upon leaving and it was in the correct working order.

We received a call from East Lansing, Michigan. The caller had explained that he would like us to come out and install a plug for his generator. When we arrived we installed a plug for the new generator, and installed wiring from the plug to the main panel. We also installed a new generator breaker in the panel. We supplied a 25ft for for the generator. We tested the plug and cord upon leaving and both were in correct working order.

We received a call from Eagle, Michigan. The caller explained that he would like us to come out and install a surge protector for the whole house. When we arrived we supplied and installed a silver grade surge suppressor. The silver grade comes with $25,000 worth of coverage.

We received a call from Potterville, Michigan. The homeowner had explained that she wanted us to come out repair their service riser. When we arrived we installed a new weather head, new straps, and a new knob for the power lines. We tested everything upon leaving and all was in correct working order upon leaving.

We received a call from Lansing, Michigan. The homeowner had called and explained that she wanted us to come out and supply and install a dimmer switch in her home. When we arrived we removed the three-way switch for the stairway lights. We supplied and installed a three-way dimmer. We tested the dimmer with upon leaving and it was in correct working order.

We received a call from Grand Ledge, Michigan. The home owner had called and explained that he wanted us to come out and install heat tape for his roof. When we arrived, we supplied  the heat tape for the back of the house, and supplied and installed the thermostat control for the heat tape. We looped the tape up the forest 2-3 foot of the roof. We installed heat tape in the gutter and down the spout.

We received a call from DeWitt, Michigan. The caller had explained that he wanted us to come out and install a plug for their generator. When we arrived we installed a 30amp plug on the outside of the house by the electrical meter. We wired from the new plug to the panel. We installed a new interlock kit on the main panel, and transferred the dryer breaker from the main panel to the sub panel.